Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Brick: What to Know First

As an independent Olympia Chimney service provider, we install, repair, and replace chimney caps and crowns on Olympia Chimney systems across Brick. Most jobs are completed in a single visit with upfront pricing agreed before we start. A standard cap replacement runs $280-$520, while crown repair or coating typically falls between $340-$780 depending on access and extent of damage.

Call (609) 657-3371

This page is for Olympia Chimney owners in Brick who’ve noticed rust streaks, water in the firebox, or crumbling mortar at the chimney top and want the fix done properly. If you’re seeing daylight through a cracked crown or your cap blew off in last winter’s nor’easter, call (609) 657-3371. A live person answers, and we’ll get you scheduled.

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia Chimney 304 stainless caps: weld-seam corrosion near the Jersey shore. The 304-grade series cap is solid equipment, but in Brick we’re close enough to the Atlantic that salt air accelerates weld-seam failure at the corners. We see this especially on homes east of the Garden State Parkway, where the cap looks fine from the ground but the seams have opened to pinholes. We replace with 316-grade stainless or match to the homeowner’s preference, and we seal the new seam with high-temp silicone rated for freeze-thaw cycling.
• Olympia Chimney multi-flue caps: improper overhang causing crown wash erosion. The multi-flue cap line sometimes gets installed with insufficient overhang past the chimney edge. Rain runs down the cap face and straight onto the crown wash instead of shedding clear. In Brick, where we get 45-plus inches of annual precipitation, that constant drip-drip erodes the crown in three to five years. We measure overhang precisely and often upsize the cap or add a drip edge to protect the crown we just repaired.
• Olympia Chimney galvanized caps: rust-through at the ten-year mark. The galvanized economy line was common on builder-grade homes in Brick’s 1990s and 2000s construction booms. Galvanizing eventually wears thin, and once rust starts it moves fast. We don’t try to paint or patch these. We pull the cap, inspect the flue tile underneath for spalling, and install a stainless replacement that outlives the mortgage.
• Olympia Chimney crown coatings: hairline cracking from thermal shock. Olympia’s crown coating products perform well when applied to sound substrate, but we’ve found they don’t bond reliably to crowns that already have active cracking wider than a sixteenth-inch. The Brick freeze-thaw cycle pops the coating off by year two. We grind out cracks wider than that, use a bonding agent, and apply the coating in two thin passes rather than one thick one. Done this way, it holds.
• Olympia Chimney custom caps: measurement drift on older chimneys. The custom cap line requires precise flue and chimney dimensions, but Brick has plenty of post-war and 1970s chimneys that have settled or been re-pointed so many times the original specs are meaningless. We measure in person with a story pole and digital caliper, never from photos alone. Russell Haines still checks these measurements himself before ordering. The cap that shows up fits the first time.

Our Olympia Chimney Chimney Cap & Crown Process

1. 1
   Call and schedule. A live person answers at (609) 657-3371, any hour. We book a window that works for you, not a four-hour guessing game.
2. 2
   Level-2 camera inspection. Our technician arrives uniformed and background-checked, sets up the camera, and documents the flue interior, crown condition, and cap attachment points. You see the photos. We explain what we’re looking at in plain English.
3. 3
   Parts decision: OEM Olympia Chimney or quality aftermarket. If your cap is under warranty and the failure is a manufacturing defect, we source OEM. For out-of-warranty work, we often recommend Gelco or Copperfield equivalents with equal or better gauge stainless at lower cost. We explain the trade-off and let you decide. No pressure.
4. 4
   The repair. For crown work, we grind, patch with CrownCoat or custom mortar, and apply the finish coat. For caps, we remove the old unit, inspect the flue tile for hidden damage, and install the new cap with proper clearance and fasteners rated for coastal wind load.
5. 5
   Test and document. We run a final camera pass to confirm no debris fell into the flue during the cap swap. We photo the finished crown or cap from multiple angles. You get the images and a written summary.
6. 6
   Cleanup and guarantee. We haul away the old cap and debris. Your work is covered by our 90-Day Done Right Promise - in writing, no arguing. If it’s not right, we come back.

What Olympia Chimney Chimney Cap & Crown Costs in Brick

These are real numbers for Brick, not bait-and-switch estimates. We agree on the price before we start. Every estimate includes the camera inspection and photo report. Call (609) 657-3371 for your exact quote - estimates are free.

Why Brick Homeowners Call Hearthstone Chimney Co. for Olympia Chimney Work

We’ve been working chimneys across Brick for over 42 years, and we’ve learned that the salt air off Barnegat Bay doesn’t negotiate with cheap materials. That’s why we use professional-grade products from Olympia Chimney, DuraFlex, HeatShield, Gelco, Famco, and Copperfield - brands that hold up to real Jersey Shore weather.

Our technicians are background-checked, uniformed, and trained on Olympia Chimney’s specific mounting systems and clearances. Most jobs finish in one visit. The price we quote is the price on the invoice. And if something’s not right, our 90-Day Done Right Promise means we make it right - in writing, no paperwork, no arguing.

Find what’s wrong, fix it properly, stand behind it - that’s the whole job.

FAQs